Choke Tubes Allow Shooters to Change their Pellet Dispersal Pattern
Choke Tubes Allow for “Quick-Change” Performance
Find the RIGHT CHOKE TUBE for every Shotgun you Own
When it comes to shotgun choke tubes, there is one name that rings true as the go to source of knowledge.
That name is Trulock.
From hunting to tactical, the team over at Trulock knows exactly what is needed to take the best shot possible. With decades of experience in engineering the world’s most efficient chokes, the team over at Trulock is second to none in knowledge as well as experience.
The story behind Trulock Choke Tubes, dates back to 1981 when founder George Trulock first began work engineering and designing his revolutionary new choke and installation system. George identified the need for a system that could be retrofitted into most shotgun barrels without the use of an adaptor or complicated machining tools. His final design accomplished just that.
Since then, George introduced a process and system that has been in continuous production, as well as being adopted by several major shotgun manufacturers as the industry standard. An inventive genius that has contributed to improve the shooting industry for all time.
To date, Trulock has a stock of approximately 2500 different chokes, with more scheduled to hit the market very soon. Trulock chokes are guaranteed to turn heads, they make competitors take notice. Folks that use them know that Trulock choke tubes are “THE brand” that everyone should look to when they need the right choke for their style of shooting fun.
This year, if you are planning to attend the 2018 SHOT Show, Trulock invites you to visit their booth #15855 and learn more about why Trulock Choke Tubes and the “Legend” behind their invention have helped to improve shotgun choke technology.
Follow Trulock for exclusive content and discount deals on Facebook, and check them out on-line at www.trulockchokes.com.
Rust, residue build-up and choke expansion CAN ALL OCCUR at the same time, making the removal of your choke tube a very difficult task.
Choke tubes frozen in place from expansion is different from rust or residue build up.
Keep in mind, however, that rust, residue build-up and choke expansion CAN ALL OCCUR at the same time.
Without getting to deeply involved in the science of metals you need to know that when a shot charge passes through a choke tube it exerts a force in two different directions. Force is applied to the choke tube when the shot charge strikes the choke forcing cone.
The first direction is longitudinal. The force in this direction simply tries to push the choke out of the barrel. This is prevented from happening by the interlocked threads on both the choke and the internal threads of the barrel. If enough force is exerted then the threads in the barrel and or the threads on the choke shear and out it goes. I have never seen a choke fail from thread shear.
The second direction is at approximately right angles to the bore. In this direction the applied force tries to make the choke expand. As the shot column moves through the choke tube forcing cone, the pellets are in constant movement to rearrange themselves so that the shot column becomes smaller in diameter and elongated. This generates a force that wants to expand the choke tube.
Factors to consider:
* Steel is elastic to some degree.
* If enough force is applied the choke tube will expand by a small amount and when the force is removed it will contract to its original size and shape.
* One of the ways we measure the strength of steel is by “Yield Strength”.
* For our purpose we can define yield strength as the maximum amount of force that is applied that does not cause any permanent deformation of the steel.
* If we increase the level of force past the yield strength of the steel used in that choke, it will expand past its elastic limit and stay in this expanded size.
* If you continue to shoot this load in this choke tube it will expand a small amount each time and at some point it will be solidly locked into the barrel.
* This force reaches its peak nominally at the intersection of the choke forcing cone and the parallel section. This is the area where choke expansion will occur.
* Choke tubes in this condition cannot be removed by normal methods.
The actual force is generated from a number of combined factors:
1. Size of steel shot. The larger the diameter of the shot the more force is created
2. Weight of the shot charge. Heavier payloads cause higher forces
3. Choke constriction. More constriction causes higher forces
4. Velocity. The higher the velocity the more force is created
Very high velocity steel shot shells with large diameter (particularly size B and larger pellets) through tighter (typically full or tighter) constriction chokes are usually the culprit causing choke expansion.
One of the best ways to prevent choke expansion is to follow the choke manufacturer’s recommendations.
* Some choke manufacturers will mark the choke “no steel” if it is not rated for steel.
* Some mark the choke “approved for steel”
* All factory chokes, as a rule, are rated for steel shot loads from cylinder bore through modified constriction, at least all that I have seen.
* If you use a factory choke tighter than modified that is not marked for use with steel, I would check it on a regular basis for choke expansion.
* If you find a choke tube that gets progressively harder to remove and replace each time you do so, examine it carefully as it is probably failing from expansion.
* If in doubt whether a choke is rated for steel, contact the manufacturer.
In my experience with steel shot I have found that if a choke does not expand with a given steel load after 25 shots it will never expand. Don’t take that as a fact as nothing is 100% when it comes to shotguns. However to date, this rule of thumb has never failed me.
While this is certainly not intended to be a true technical paper, hopefully it has given you a basic understanding of why choke tubes can and do freeze in the barrel.
For more information on Trulock Choke Tubes, visit http://www.trulockchokes.com.
Sincerely,
George Trulock
1-800-293-9402 work; 229-762-4050 fax
Email: trulock@trulockchokes.com
I’m sure a lot of shotgun shooters have encountered this dreaded problem.
You start to remove the choke from your shotgun and it will not budge.
You increase the pressure on your choke wrench and still get no movement.
You eventually end up putting enough torque on the wrench that it causes your face to turn red and your arms too start to tremble. The choke still does not move.
You then find some sort of tool to give you additional leverage on the wrench and the darn choke tube still refuses to budge.
You start to wonder what you did to cause this problem!!
There are BASICALLY THREE THINGS THAT WILL FREESE UPA SHOTGUN CHOKE IN THE BARREL:
Rust
Residue build up from fired shells (unburned powder, fiber, plastic, etc.)
Choke tube expansion (Creep)
If you want to keep your shotgun chokes functioning as they were intended, then TAKE CARE OF THESE BASIC MAINTENANCE ITEMS ON A REGULAR BASIS:
LOOSEN & RETIGHTEN the choke on occasion. Even better if you REMOVE the choke and REINSTALL in the barrel on a regular basis. This will break any bond that is attempting to form.
CLEAN CHOKE BODY and REMOVE RESIDUE from the threads with a stiff brush and solvent of some kind.
CLEAN INTERNAL THREADS and CHOKE COUNTERBORE in the barrel. USE BRONZE BORE BRUSH and SOLVENT.
WIPE SURFACES DRY, then LUBRICATE them with a few drops of high quality GUN OIL.
From hunting to tactical, the team over at Trulock knows exactly what is needed to take the best shot possible. With decades of experience in engineering the world’s most efficient chokes, the team over at Trulock is second to none in knowledge as well as experience.
Since then, George introduced a process and system that has been in continuous production, as well as being adopted by several major shotgun manufacturers as the industry standard. An inventive genius that has contributed to improve the shooting industry for all time.
